Wednesday, 4 July 2018

latest SP FLASH TOOL V.5.1820

SMART TELECOM1 July 04, 2018 No comments

latest SP FLASH TOOL V.5.1820

FRIENDS THIS IS VERY LATEST VERSION OF

SP FLASH TOOL WITH THIS TOOL WE CAN

FLASH ALL MTK CPU DEVICES SO HERE W

ARE PROVIDING GENUINE LINK OF OFFICIAL

WEBSITE OF SP TOOL SO DOWNLOAD FROM

THERE AND ENJOY,

THANK YOU LIKE SHARE AND SUBSCRIBE OUR YOUTUBE CHANNEL AND SUPPORT US......

LINK IS HERE

DOWNLOAD ALL USB DRIVERS IN ONE SINGLE FILE AND INSTALL EASY

SMART TELECOM1 July 03, 2018 No comments

DOWNLOAD ALL USB DRIVERS IN ONE SINGLE FILE AND INSTALL EASY

CLICK THIS BUTTON TO

BATTERY KE VOLTAGE KO KAISE CHECK KARE

SMART TELECOM1 July 02, 2018 SMARTTELECOM1 BATTERY VOLTAGE CHECK No comments

BATTERY KO KAISE CHECK KARE

FULL DETAIL INFORMATION

A good and working battery voltage is approximately 3.7 volts DC(direct current),

below that maximum voltage range the phone will not be able to power on.

Checking the battery voltage by Digital multi-meter is so easy,

just set it to a DC range 20volts then attach the both test probes to each corresponding polarity,

positive probe to positive terminal, then negative probe to negative battery terminal.

Check the maximum battery voltage reading 3.7 volts.

A battery voltage lower than 3.7 volts can power on the handsets but it shows Battery Low on a screen.

A battery voltage lower than 2 to zero volts will hardly charge the phone and won't power up the phone.

EASY STEP HOW TO CHECK FOLLOW HERE

Step 1.

Turn off your cell phone and open up the battery compartment.

Step 2.

Remove the battery and set it down on a flat surface so the terminals are facing you.

Step 3.

Identify the two terminals on the battery that are labeled with a "+" and a "-" sign.

Then, look on the battery's label to find out how much voltage it is rated at.

For instance, on the battery pictured, the voltage is rated at 3.7 VDC, or approximately 4 volts DC.

Touch the tip of the red probe to the terminal labeled " + ." Keep them in contact while you press the tip of the black probe to the terminal labeled " - ."

Check the digital reading on your multimeter to see how much charge the battery has. In this case, the battery has a 4 volt DC charge. It is fully charged.

A drain battery voltage approximately down to zero volts will not be able to accept charge when a charger is being plug-in.

A drain battery will be shock by a a higher voltage range from 6 to 12 volts for a quick charging point as possible to avoid damaging the battery,

a DC regulated power supply. is the equipment used to shock a drained battery.just connect both probe to each corresponding polarity for a quicker period of time,

prolonging it will damage the battery itself. You may ask an experience technician in your neighborhood

about this method for assistance and safety guidelines.

WATCH VIDEO TILL THE END TO UNDERSTAND CORRECT.

SUBSCRIBE OUR YOUTUBE CHANNEL

full short, half short & 0k condition & what is shorting in mobile phones:

SMART TELECOM1 July 02, 2018 1 comment

Full short, half short & 0k condition

what is shorting in mobile phones:

The first thing you have to check in dead mobile phones after checking the battery is shorting. And if it is short, you will first have to remove it to get it repaired. All technicians should know how to remove a short circuit in cell phones.

Reasons for shorting in mobile phones:

Phone falling in water. This is the most common reason

Handset overheating.

Using an incompatible or faulty charger for charging

Sometimes, sparks or smoke coming out of the handset due to any reason.

We have to understand the below 2 terms of electronics to understand shorting better:

Open circuit: If a track is broken, then it is said that the track is open.

Short circuit: If 2 parallel separate tracks touch each other due to some fault, it is called short circuit.

important information read till the end...

Note: In circuit boards of cell phones, tablets or any other electronic device, there are tracks instead of wires through which current flows. Hence we use the term ‘tracks’ instead of wires or cables.

Option 1.

How to check shorting in mobile phones with multimeter:

We can easily check whether there is shorting in the circuit board or not with the help of a multimeter. Follow the steps below:

Keep the multimeter on continuity setting (Also called diode setting)

Identify the positive and negative terminals of the battery connector. The positive terminal (+) is the pin of the battery connector where the positive terminal of the battery touches on it. It is also called vBat (Battery Voltage) pin. While negative terminal (-) is the pin of the battery connector where the negative terminal of the battery touches on it. It is also called GND (Ground) pin.

Now touch the red probe (+) of the multimeter to negative terminal of the battery connector.

If you see any reading on the multimeter or hear a continuous beep sound, then the motherboard is short i.e your mobile phone is short.

And if there is no reading or no continuous beep sound, the board is not short.

If you are using an analogue multimeter, keep it on Ohms(x10) setting.

If the pointer (needle) moves even a little, than it is short, otherwise, it’s okay.

Option 2.

How to check shorting in mobile phones with DC Power Supply:

A DC Supply is also called jhatka machine or battery eliminator. Its work is to convert AC voltage coming from an AC volt source to DC voltage. To check shorting, follow the step below:

Switch on the DC power supply. Now select the output voltage as much as its battery voltage. You can read it on the battery. In most phones, it is 3.7v or 3.8v. Some Chinese phones have output of 4.2 volt.

Connect red probe to the positive terminal of the battery connector (vBat pin) and the black probe to the negative terminal (GND)as well as the 3rd pin called BSI. And do not touch any other key or button.

Now, if you see any amount of current on the screen, then it means, the circuit board is short.

And if, there is the screen shows ‘0.00’ in the current reading, then it is okay.

Problems in handset if it is short:

Dead

Battery drains and discharges fast

Overheating

Hanging

Switches off automatically or restarts.

Learn How to use multimeter in mobile phone repairs.

If the circuit board is short, you will first have to remove shorting for fixing the problem, especially, if the handset is in dead condition. Learn how to remove shorting in mobile phones.

Note: The above procedure to check shorting is the same for all brands of cell phones and tablets including Samsung, iPhone, Nokia, Sony, HTC, Motorola and Chinese handsets. It will be the same for all smartphones be it based on iOS, android or Windows OS.

WATCH FULL VIDEO

SUBSCRIBE OUR

YOUTUBE CHANNEL

Please let us know your results in the comments section below.

NCK DONGLE CRACK VERSION FOR FRP REMOVE MTK OPPO VIVO

SMART TELECOM1 July 02, 2018 No comments

NCK DONGLE CRACK VERSION

FOR FRP REMOVE MTK OPPO VIVO

LINK ONE

LINK TWO

EK WEBSITE JISME APKO SAARE FLASH FILE MILJATE HAI

SMART TELECOM1 June 30, 2018 No comments

EK WEBSITE JISME APKO SAARE FLASH FILE MILJATE HAI

Friends in this website we can download each and all models mobile software flash files or stock rom this is very good website where we can download very easy method.

so use this website and download all flash files absolutely free.

If you like our channel plz like share subscribe & comment and support us to help others who is very new in this mobile repairing field.

So thank you friends lets be in touch with us.....

CLICK DOWNLOAD BUTTON TO DOWNLOAD ALL FLASH FILES